MP-SPR in soft materials

AN136_Polymer_Collapse_schema.jpgSoft materials is a general term usually used for polymeric materials, especially when dealing with materials in solution. In general, the term “soft materials” is used in literature with almost anything that can dissolve into solvents.

Typical end applications of soft materials being developed are implant coatings and implants, biodegradable materials, intelligent materials for coatings (active corrosion protection), intelligent drug dosing, targeted drug delivery, 2-dimensional cell growth matrixes and other similar areas where interaction or release of something from the material needs to be achieved. In addition, these are sometimes used as barrier coatings (gas permeation barriers), display materials, organic electronics, OLEDs, organic solar cells and in implant coatings.

MP-SPR Navi™ instruments have been used extensively in research of different nanoscale materials, such as hydrogels for contact lenses to be both biocompatible but antimicrobial and drug-loaded functional material which trigger on contact with microbes on implant surfaces. Also, the MP-SPR method has been used to make new antifouling coating materials for marine environment to prevent algae, bacteria and shellfish attachment.

The MP-SPR technology has been developed especially for material testing, originally in liquid environment. Experiments with biocoatings (bioresistant, biocompatible or bioactive) were performed, using the BioNavis MP-SPR technology extensively. The technology can both characterize the coating properties (up to microns in thickness, and refractive index) as well as the desired interactions, swelling or resistance of the coating.

Applications for MP-SPR in soft materials research:

  • Layer-by-Layer deposition monitoring
  • Monitoring stimuli-response
  • Monitoring coating deposition (in-situ or ex-situ)
  • Calculation interaction kinetics or magnitude
  • Gas permeation monitoring for barrier coatings
  • Monitoring formation of self assembled layers or coatings
  • Drug release from polymer matrix

Benefits of MP-SPR in soft materials research:

  • Water / solvent swelling does not interfere
  • Thickness of polymers up to 5 µm
  • Thickness and RI can be measured in same experiment as the interaction
  • Pure kinetics, unique reduction of environmental artefacts
  • On-line monitoring of nanofabrication (LbL)
  • Sensitivity
  • Electrochemistry-SPR combination
  • Proven peer-reviewed record in LbL, LB, interaction and cellulose research
  • Sensor recycling often possible (total cost of ownership)
  • No oil, contamination free continuation to AFM, XPS, etc.
  • Prism not integrated to substrate – substrate can be used after MP-SPR measurement to measure AFM, XPS, etc.

Selected publications:

See selected Application Notes to see that MP-SPR works:

  • AN#158 Predicting cellulose nanocrystals dispersibility using MP-SPR
  • AN#154 Real-time cancer cell detection and cell adhesion on implant materials surface
  • AN#150 Organophosphonates characterization using MP-SPR
  • AN#149 Polymer characterization using MP-SPR - Adsorption studies and layer thickness
  • AN#136 Polymer collapse due to pH or electric potential change monitored with MP-SPR
  • AN#135 Gas induced surface changes measured with MP-SPR
  • AN#131 Deep scanning SPR (waveguide) mode for characterization of thicker (300 nm to microns) layers and their interactions using MP-SPR technology
  • AN#128 Thickness and refractive index of dielectric layers using multiple wavelengths or multiple media
  • AN#112 In situ monitoring of metal-organic framework assembly by SPR
  • AN#111 Real-time characterization of polyelectrolyte multilayers using Surface Plasmon Resonance (SPR)
  • AN#109 Langmuir-Blodgett film characterization in air using Surface Plasmon Resonance (SPR)

 

See five reasons to choose MP-SPR for soft materials.


Optimal MP-SPR setup for soft matter applications

  • MP-SPR Navi™ 210A VASA: 6-sample automated liquid handling instrument with two liquid channels

  • Additional lasers L-option to ensure conformation based on layer thickness and refractive index information

  • BioNavis LayerSolver™ for calculating thickness and refractive index information

  • TraceDrawer for MP-SPR Navi software to determine affinity and kinetic parameters